TPMS Reset Procedure
Make:Chevrolet Model:Silverado 3500 HD Sub-Model:LT Year:2008, 2011, 2012, 2013, 2014, 2015
Required Tools
Properly formatted scan tool or trigger tool.
 

Preparation

1.   Review all data in your owner's manual pertaining to the TPMS System
2.   Verify vehicle application is covered by Trigger Tool
3.   Update Trigger Tool Software
4.   Verify that the Trigger Tool is working properly (replace battery if necessary)
  
Installation

NOTE: This Step should be performed only by a technician who has been properly trained in the operation and installation of TPMS Systems.

    • Install Sensors - Properly Install tire pressure sensors.
    • Tire Pressure - Confirm all tires are inflated to the pressure indicated on the tire pressure placard.(Placard is located on the driver's side door jamb of vehicle)


      This is a sample Tire Pressure Placard.  Not for this specific vehicle.

    • Eliminate Interference - To ensure the control unit memorizes the correct sensor ID's, the vehicle with    a new sensor must be at least 3m (10 ft.) from any other TPMS pressure sensor not installed on that vehicle.

Relearn
 
STANDARD IGNITION

1. Engage parking brake.

2. Turn ignition switch to ON position (engine off).

3. Enter Re-Learn Mode 

Remote Keyless Entry (RKE) Method

Press and hold the transmitter’s LOCK and UNLOCK buttons at the same time for approximately 5 seconds. The horn will sound twice and the Left Front Turn Signal will illuminate to indicate that the receiver is in the learning mode. “TIRE LEARNING ACTIVE” will be displayed on the DIC, Driver’s Information Screen.  Proceed to step 4.

Driver Information Center (DIC) Method

Press the Driver Information Center (DIC) vehicle information button until the PRESS ? TO RELEARN TIRE POSITIONS message displays. The horn will sound twice and the Left Front Turn Signal will illuminate to indicate that the receiver is in the learning mode. TIRE LEARNING ACTIVE will be displayed on the DIC, Driver’s Information Screen.  Proceed to step 4.

Trip Odometer Method

Press the trip odometer reset stem located on the instrument panel cluster until the PRESS ? TO RELEARN TIRE POSITIONS message displays. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen.  Proceed to step 4.

WITH PUSH BUTTON IGNITION
  •  Press and hold the push button start until the vehicle is in accessory mode.

    NOTE: On Cadillac models you will know when you are in accessory mode when the Cadillac emblem appears on the DIC.

  • Press the MENU button located on the turn signal lever until "VEHICLE INFORMATION MENU" is displayed.
  • Once you are in the VEHICLE INFORMATION MENU, use the arrow buttons on the turn signal lever until the DIC displays the vehicle's tire inflation pressures and positions.
  • Press and hold the button located on the end of the turn signal lever until "Are you sure that you want to relearn? YES or NO" is displayed.
  • Use the arrow buttons on the turn signal lever to highlight YES. Once YES is highlighted, press the button located on the end of the turn signal lever. The horn will sound twice and the Left Front Turn Signal will illuminate to indicate that the receiver is in the learning mode. “TIRE LEARNING ACTIVE” will be displayed on the DIC, Driver’s Information Screen.  Proceed to step 4.
4. Starting with LF tire, increase/decrease tire pressure until horn sounds or place scan tool near the sensor and press the activate/trigger button.
 


NOTE: You must use a scan tool to trigger/activate the TPMS sensors on all 2012 and newer model year GM vehicles. Increasing/Decreasing the air pressure will not trigger/activate the sensors.

5. After horn sounds, repeat the previous step for the next 3 sensors in the following order: Right Front, Right Rear, and Left Rear. After Left Rear tire has been learned, the horn will sound twice indicating that all 4 sensor ID’s have been learned. The learn mode is no longer active and the TIRE LEARNING ACTIVE message on the DIC will go off.

6. Turn ignition to OFF position. Adjust all tires to pressure listed on tire pressure placard.
 

NOTE: If no tires learned are learned after entering the TPMS into Learn Mode, or if communication with the receiver stops, or if the time limit has expired, turn the Ignition Switch to LOCK/OFF and start over at step 2.



DISCLAIMER:

All information is to be used as a reference only. Vehicle information is compiled from available manufacturer sources but accuracy is not guaranteed. The application information presented in this document is accurate to the best of our knowledge and is regularly updated with the latest data available in the marketplace. Due to the vast number of car models and spare parts from numerous vehicle manufacturers the exact application of parts is not always feasible. Always reference our website for the most up to date data. Damage claims on the basis of data in this catalog will not be considered.

© Revolution Supply Co. Inc. 2013